Balluff BVS HS-Q Series Page 119 Operation Manual Download | Manualshive

Page: 119 / 296

background image

119

www.balluff.com

BVS HS-Q Series
Standard Hand Held Barcode Reader

Enter/Exit Programming Mode

4

Configuration Using Barcodes

Code 128 Function Character Transmission

Enables/disables transmission of Code128 function characters 1, 2, 3, and 4.

Code 128 Quiet Zones

This feature specifies the number of quiet zones for Code 128 labels. Quiet zones are blank areas
at the ends of a barcode and are typically 10 times the width of the narrowest bar or space in the
label.

Code 128 Function Character Transmission =

Don’t Send

Code 128 Function Character Transmission =

Send

Code 128 Quiet Zones = Quiet Zones on two

sides

Code 128 Quiet Zones = Small Quiet Zones on

two sides

DEFAULT

C8TF00(CR)

C8TF01(CR)

$CC8-

$CC8-

DEFAULT

«
...
117
118
119
120
121
...
»

Summary of Contents for BVS HS-Q Series









































































































































































































































































































Reviews:

No comments

Related manuals for BVS HS-Q Series

Brand: Datalogic Pages: 160

Brand: Magtek Pages: 41

Brand: Magtek Pages: 34

Brand: Magtek Pages: 34

Brand: Magtek Pages: 4

Brand: Magtek Pages: 44

Brand: Magtek Pages: 23

Brand: UGREEN Pages: 24

Wearable Ring Scanner

Brand: M3 Mobile Pages: 35

Brand: Fermax Pages: 10

Brand: Intermec Pages: 28

QuickScan L QD2300

Brand: Datalogic Pages: 32

Brand: Mode com Pages: 12

QuickScan QBT2400

Brand: Datalogic Pages: 56

Brand: AUDIOLINE Pages: 2

Brand: ACS Pages: 22

PRD-09695-004 - SMART Card Reader

Brand: Blackberry Pages: 28

Brand: Datalogic Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands