background image

Balluff Network Interface /

 

EtherNet/IP

 BNI EIP-950-000-Z009

 

 

www.balluff.com 

 

2

 

Safety 

2.1

 

Intended use

 

  The BNI EIP-950-000-Z009 serves as an unmanaged switch module for connecting to an 

EtherNet/IP™ network. 

 

2.2

 

Installation and 
startup 

 

 

 

Note 

Installation and startup are to be performed only by trained specialists. Qualified 
personnel are persons who are familiar with the installation and operation of the 
product, and who fulfills the qualifications required for this activity. Any damage 
resulting from unauthorized manipulation or improper use voids the anufacturer's 
guarantee and warranty. The Operator is responsible for ensuring that 
applicable of safety and accident prevention regulations are complied with. 

 

 

2.3

 

General safety 
notes

 

 

Commissioning and inspection 

Before commissioning, carefully read the operating manual. 
The system must not be used in applications in which the safety of persons is dependent on 
the function of the device. 

Authorized Personnel 

Installation and commissioning may only be performed by trained specialist personnel. 

Intended use 

Warranty and liability claims against the manufacturer are rendered void by: 

 

Unauthorized tampering 

 

Improper use 

 

Use, installation or handling contrary to the instructions provided in this operating 

manual 

Obligations of the Operating Company 

The device is a piece of equipment from EMC Class A. Such equipment may generate RF 
noise. The operator must take appropriate precautionary measures. The device may only be 
used with an approved power supply. Only approved cables may be used. 

Malfunctions 

In the event of defects and device malfunctions that cannot be rectified, the device must be 
taken out of operation and protected against unauthorized use. 
Intended use is ensured only when the housing is fully installed. 

 

Hazardous 
voltage

 

 

 

Note 

Disconnect all power before servicing equipment. 

 

 
 

 

 

Note 

In the interest of product improvement, the Balluff GmbH reserves the right to 
change the specifications of the product and the contents of this manual at any 
time without notice. 

 

 
 
 

Summary of Contents for BNI EIP-950-000-Z009













Reviews: