Balluff BDD 750 P Series User Manual Download Page 26

 

26 

 

5.9. 

Display Menu

 

 

COLOR 

This parameter defines the display color. 
Event-

depending change of the display color by a switching condition is possible (see PRESELECTION 1…4 

MENU) 

 

0  RED 

Red display 

1  GREEN 

Green display 

2  YELLOW 

Yellow display 

 

BRIGHTNESS (%)

 

This parameter defines the brightness of the display in percent

 

 

10 

Min. brightness  

90 

Default value 

100 

Max. brightness  

 

CONTRAST 

This parameter defines the viewing angle. 

 

Viewing angle from top 

Viewing angle from centre 

Viewing angle from bottom 

 

SCREEN SAVER (S) 

This parameter defines the time in seconds until the display is switched off. 

 

No switch off 

… 

 

9999 

Longest time to switch off 

 

UP-DATE-TIME (S) 

This parameter defines the update time in seconds of the display only. 

 

0,005 

Shortest update time 

0,1 

Default value 

9,999 

Longest update time 

 

FONT 

This parameter defines the setting of the font style. 

 

Standard 

Font 1 

 

SKIP COMMANDS 

This parameter is used to share or skip the display of keyboard commands. 

 

SHOW COMMAND 

KEY 

The display and execution of the commands is released 

SKIP COMMAND 

KEY 

The display window for commands is skipped 
 

Summary of Contents for BDD 750 P Series





































Reviews: