manualshive.com logo in svg

Bailey infi 90 Modular Power System II, Instruction

Share
Download
Bailey infi 90 Modular Power System II Instruction Download Page 28

INSTALLATION

CABLE INSTALLATION

I-E96-427B   

2 - 13

Table 2-1.  TMF Cable Applications, Connections and Length Requirements

Cable

 Connections

Maximum 

Length

From

 To

Meters

(Feet)

Device

Connector

Device

Connector

HCBL01

DCE or DTE device

DB-25

NTMP01

P5 or P6

15 (50)

1

NKSE01 or 
NKSE11

NTMF01

P2

NTCS04

P4 or P5

61 (200)

NKTU01 or 
NKTU11

NTMF01

P1

Primary module

P3

 

61 (200)

P3

Redundant module

NOTE:

1. The specified maximum length only applies to the HCBL01 cable. The performance of INFI 90 modules does not place a restriction on
the maximum length of the RS-232-C cable. Follow industry-wide accepted RS-232-C practices and rules when selecting a suitable
RS-232-C cable for your system.

Figure 2-13.  Cable Connections with Redundant MFC Modules, Serial Link

to a Station and Serial Ports

IMMFC03

P3

IMMFC03

P3

PRINTER

T00746A

COMPUTER

P1

P3

J1

J2

P2

P1

P5

P4

NTCS04

NTMF01

NKTU01/11

NKTU01/11

RS-232-C

RS-232-C

NKSE01/11

PORT 1

TO

STATION

PORT 2

P3

P2

Summary of Contents for infi 90 Modular Power System II























































Reviews:

No comments

Brands by name

Popular brands

Load more brands