background image

pBS2120 Base Station Installation Guide 

 

 

The ground wire adopts yellow-green wire that is no smaller than 16 mm². 

 

Grounding principle: as near as possible. 

 

The eNodeB connects to the reliable outdoor grounding point (earth) through one 

ground screw. 

 

The  connection  of  the  grounding  points  and  the  ground  bar  need  to  be  tight  and 

reliable.  Rustproofing  the  terminals  is  required.  This  can  be  done  with  rust 

preventing paint, anti-oxidation coatings, grease, and so on. 

 

Regulatory Compliance 

3.6

FCC Compliance 

This device complies with part 15 of the FCC Rules. Operation is subject to the 

following two conditions: (1) This device may not cause harmful interference, and 

(2) this device must accept any interference received, including interference that 

may cause undesired operation. 

Any Changes or modifications not  expressly approved by  the party  responsible 

for compliance could void the user's authority to operate the equipment . 

This equipment has been tested and found to comply with the limits for a Class A 

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to 

provide reasonable protection against harmful interference when the equipment 

is operated in a commercial environment. This equipment generates, uses, and 

can radiate radio frequency energy and, if not installed and used in accordance 

with  the  instruction  manual,  may  cause  harmful  interference  to  radio 

communications.  Operation  of  this  equipment  in  a  residential  area  is  likely  to 

cause harmful interference in which case the user will be required to correct the 

interference at his own expense. 

Warning 

This  equipment  complies  with  FCC  radiation  exposure  limits  set  forth  for  an 

uncontrolled environment. This equipment should be installed and operated with 

minimum distance 30 cm between the radiator & your body. 

 

ISEDC Compliance 

This device complies with Innovation,  Science,  and  Economic  Development 

Canada licence-exempt RSS standard(s).  

Operation is subject to the following two conditions: (1) This device may not  

Summary of Contents for pBS2120

















Reviews: