Badger Meter ModMAG M1000 User Manual Download Page 3

Basic safety recommendations 

Page 1 / 23 

 

MID_VD_BA_02_1607 

1. Basic safety recommendations 

Before installing or using this product, please read this instruction manual thoroughly. 
Only qualified personnel should install and/or repair this product. If a fault appears, 
contact your distributor. 
 

Installation 

Do not place any unit on an unstable surface that may allow it to fall. 
Never place the units above a radiator or heating unit. 
Route all cabling away from potential hazards. 
Isolate from the mains before removing any covers. 
 

Power connection 

Use only the type of power source suitable for electronic equipment.  If in doubt, contact 
your distributor. Ensure that any power cables are of a sufficiently high current rating. 
All units must be earthed to eliminate risk of electric shock. 
Failure to properly earth a unit may cause damage to that unit or data stored within it. 
 

Protection class 

The device has protection class IP 46 and needs to be protected against dripping water, 
water, oils, etc. 
 

Setup & operation 

Adjust only those controls that are covered by the operating instructions.  Improper 
adjustment of other controls may result in damage, incorrect operation or loss of data. 
 

Cleaning 

Switch off all units and isolate from mains before cleaning.   
Clean using a damp cloth.  Do not use liquid or aerosol cleaners. 
 

Repair of faults 

Disconnect all units from power supply and have it repaired by a qualified service person if 
any of the following occurs: 

  If any power cord or plug is damaged or frayed 

  If a unit does not operate normally when operating instructions are followed 

  If a unit exposed to rain/water or if any liquid has been spilled into it 

  If a unit has been dropped or damaged 

  If a unit shows a change in performance, indicating a need for service. 

 

RoHs

 

Our products are RoHs compliant. 

 

Battery disposal 

The batteries contained in our products need to be disposed of as per your  
local legislation acc. to EU directive 2006/66/EG. 

 
 
 

Failure to adhere to these safety instructions 

may result in damage to the product or serious 

bodily injury. 

 

Summary of Contents for ModMAG M1000



























Reviews: