BAB TECHNOLOGIE DUODMX GATEWAY Documentation Download Page 15

Page: 15 / 52

DUO DMX

Gateway

Programming

DUO DMX

Gateway

b.a.b-technologie gmbh 15

PROGRAMMING

The programming of the DUO

DMX

Gateway is done over the DMX-Configurator. There the scenes are

set up, the Group Addresses resp. EnOcean Profiles are linked to the dim outputs or the scenes. The

configuration is transferred over the network or over an SD-card into the device.

5.1

ENABLING THE (DMX-) PREVIEW

In conjunction with the DUO

DMX

GATEWAY the

"DMX Configurator"

software provides a so called

"DMX Preview.

In the Preview all changes made to the DMX channel controllers are made directly visible

on the terminal device. In this way, the sequences and scenes can be directly tested and modified if

necessary, without having to transfer the configuration first.

Note: Please note that the DMX Preview transmits permanent values for as long as the DMX Configurator

is opened and the Preview is activated. If you were then to try and control the DMX channels by means

of the respective bus system, its commands would be overwritten by those of the active preview. Make

sure that you only use either the preview or the corresponding control system (KNX, BMX, EnOcean ).

The preview can be done in two ways

Broadcast Preview:

All DUO

DMX

GATEWAY in the network are addressed using the preview no

matter what network settings you have and whether they just allow the PC from the DMX-

Configurator to be started. The preview will be sent via Broadcast signals into the network.

Unicast Preview:

Only a selected DUO

DMX

GATEWAY receives the preview signals. It is

important to note, that the desired gateway and the PC are within the same network area. The

signals are sent via Unicast to a specific IP address.

Which of the two DMX outputs are used for the Preview signals can be choose. To activate the preview,

go to the menu "

Extensions

"> "

DUO-DMX Gateway

Activation of the broadcast Preview

To activate the broadcast preview just one of the two (or both) checkboxes "

DMX Out 1

" or "

DMX Out

” has to be selected. Choose your selection and confirm with “

”. From now on, the preview will be

sent via broadcast signals into the network and interpreted by all available gateways.

Figure 12: Broadcast Preview

Summary of Contents for DUODMX GATEWAY





















































Search results

Summary of Contents for DUODMX GATEWAY

Reviews:

Brands by name

Popular brands

BAB TECHNOLOGIE DUODMX GATEWAY, Documentation

Search results

Summary of Contents for DUODMX GATEWAY

Reviews:

Brands by name

Popular brands