manualshive.com logo in svg

BAB TECHNOLOGIE APPMODULE IP, Documentation, Page: 54 / 62

Share
Download
BAB TECHNOLOGIE APPMODULE IP Documentation Download Page 54

 

 

APP

MODULE Documentation 

 

54  BAB TECHNOLOGIE GmbH 

 

 

8.7

 

REM  OTE SERVICING 

Remote Servicing is available as of firmware version 1.3.7.  

 

Activate the Remote Servicing Access of the APPMODULE. Select a time between 2-12 hours after which 

the Remote Servicing Access is automatically closed. Remote Servicing Access is also deactivated again 

if the APPMODULE is restarted, this is independent of the set time. Remote Servicing Access can be 

deactivated at any time by clicking on "Deactivate Remote Servicing Access". 

Activate the Remote Servicing Access by clicking on "Activate Remote Servicing Access". 

Remote Servicing access is started. This process takes a few seconds and the Remote Servicing Access ID 

is displayed. Copy the ID and send it to 

[email protected]

. 

 

 

Figure 53: Remote servicing 

 

Before you activate Remote Servicing Access, contact Support. 

 

 

 

Summary of Contents for APPMODULE IP































































Reviews:

No comments