background image

BL4, BL4-C

93288, 93284

Operating Manual

7

The BL4 is a motion detector for ceiling mounting having a circular detection area. 
The BL4-C is a ceiling-mounted motion detector with a narrow, elongated detection range especially

for corridors. 
Settings can be made with the IR-BL infrared remote control.

3.2

Functions

The  general  operation  of  the  motion  detector  is  described  in  the  short  operating  instructions

supplied with the device. 
Passive  infrared  motion  detectors  register  movements  of  heat  sources  and  convert  them  into

signals that are evaluated by a processor. 
The  device  is  a  switching  detector.  The  brightness  value  below  which  the  illumination  is  to  be

switched on can be freely selected (switch-on threshold).
If the value measured by the light sensor is below the set switch-on threshold, a detected move

-

ment causes the connected illumination to switch on. The follow-up time also restarts with each

newly detected movement. After the follow-up time has elapsed, the illumination is switched off.
The illumination can be switched on or off manually by remote control at any time. The device then

remains switched on or off as long as movement is detected plus the set follow-up time.
The follow-up time is restarted by each movement detected. If no movement is detected during a

follow-up time, the detector returns to normal operation (light is switched on during movement and

remains on until no movement is detected for a follow-up time).

Summary of Contents for Luxomat BL4
































Reviews: