manualshive.com logo in svg

B+B SmartWorx SPECTRE v3 LTE, User Manual, Page: 22 / 50

Share
Download
B+B SmartWorx SPECTRE v3 LTE User Manual Download Page 22

5. ROUTER DESIGN

5.7

Description of the rear panel

The rear panel contains only two holders for SIM cards (

SIM1

and

SIM2

), holder for SD

card (

SD

) and

RST

button used to restore default configuration and reboot the router.

5.8

Description of the front panel

On the front panel is the following:

Caption

Connector

Description

PWR

2-pin

Connector for the power supply

ETH0

RJ45

Connector for connection into the computer network

ETH1

RJ45

Connector for connection into the computer network

ANT

SMA

Connector for main antenna

DIV

SMA

Connector for diversity antenna

GPS

SMA

Connector for GPS antenna

WiFi

R-SMA

Connector for WiFi antenna (

only for versions with WiFi

module!

)

USB

USB-A 2.0
Host

Connector for connection of USB devices to the router. Sup-
ports devices with PL-2303 and FTDI USB/RS232 converters.

I/O

6-pin

Connector for connection of the binary inputs and output

Table 8: Front panel description

Figure 24: SPECTRE v3 LTE front panel

14

Summary of Contents for SPECTRE v3 LTE



















































Reviews:

No comments