B+B SmartWorx SPECTRE v3 LTE User Manual Download Page 18

Page: 18 / 50

5. ROUTER DESIGN

5.2

Delivery identification

Trade name

Type name

Other

SPECTRE v3 LTE

SPECTRE-v3-LTE

Router in a plastic or metal box

Table 2: Delivery identification

Figure 20: Label example

5.3

Ordering codes

Ordering codes overview is shown in the table below.

Name

Order code

Features – interfaces

SPECTRE v3 LTE set

SR3xx000yz

∗

LTE module, 2x ETH, 1x USB, 2x BI, 1x BO, 1x mi-
croSD reader, 2x SIM reader

SPECTRE v3 LTE set

SR3xx100yz

∗

LTE module, 2x ETH, 1x USB, 2x BI, 1x BO, 1x mi-
croSD reader, 2x SIM reader, WiFi

SPECTRE v3 LTE set

SR3xx001yz

∗

LTE module, 5x ETH, 1x USB, 2x BI, 1x BO, 1x mi-
croSD reader, 2x SIM reader

SPECTRE v3 LTE set

SR3xx101yz

∗

LTE module, 5x ETH, 1x USB, 2x BI, 1x BO, 1x mi-
croSD reader, 2x SIM reader, WiFi

SPECTRE v3 LTE set

SR3xx002yz

∗

LTE module, 2x ETH, 1x USB, 2x BI, 1x BO, 1x mi-
croSD reader, 2x SIM reader, RS232

SPECTRE v3 LTE set

SR3xx003yz

∗

LTE module, 2x ETH, 1x USB, 2x BI, 1x BO, 1x mi-
croSD reader, 2x SIM reader, RS232, RS485

SPECTRE v3 LTE set

SR3xx103yz

∗

LTE module, 2x ETH, 1x USB, 2x BI, 1x BO, 1x mi-
croSD reader, 2x SIM reader, WiFi, RS232, RS485

Table 3: Ordering codes overview

∗

Replace the letters "xx", "y" and "z" with the values from the tables on the following page.

Summary of Contents for SPECTRE v3 LTE



















































Search results

Summary of Contents for SPECTRE v3 LTE

Reviews:

B+B SmartWorx SPECTRE v3 LTE, User Manual, Page: 18 / 50

Search results

Summary of Contents for SPECTRE v3 LTE

Reviews: