Azbil MVC10A User Manual Download Page 53

Page: 53 / 64

Azbil Corporation

Maintenance and troubleshooting of this instrument

Model: MVC10A/10F - Multivariable Air Flow Meter 5-5

5-2:

Troubleshooting

Types of troubles

The following three types of troubles are conceivable when activating and starting

this instrument:

Such troubles that occur when the actual service conditions differ from the

specifications of this instrument

Troubles caused by the setting and operating errors
Troubles due to the failure of this instrument

If any trouble occurs, follow the troubleshooting guide described here and take proper

actions.

Troubles at the start of operation

Troubleshooting

If any trouble occurs, take remedial actions in accordance with the following

tabulated instructions. If the trouble cannot be solved even after taking these actions,

this instrument may be malfunctioning. Then, please contact our sales representatives

at our branch, sales office, or our distributors where you purchased this instrument, or

our customer services department of our head office.

Trouble

Check points and remedies

Nothing appears on the display after

turning on the power switch.

•  Ensure that the power supply voltage is correctly applied.
•  Ensure that power supply cable is connected.
•  Ensure that the fuse is not blown.

No output is transmitted even if the

power is turned on.

• Ensure that the signal lines are correctly connected.

No pulse output is given.

• Ensure that the pulse output lines are correctly wired.

Indication of flow rate remains

unchanged at the zero point.

• Ensure that the details of settings are correct.
•

Ensure that the flow rate is not deviating from the low

flow cut range.

• Ensure that the piping is not clogged.

While the flow rate should be zero, a

value other than zero is indicated.

•

Even a minimal deviation from the zero point may be

indicated in a large value in the scale of

/day and

hour. If this is the case, either change the indication unit

or conduct the zero adjustment or set a low flow cut

value.

• Ensure that the polarity of detector terminals and

connection of the converter are correct.

Summary of Contents for MVC10A

































































Search results

Summary of Contents for MVC10A

Reviews:

Related manuals for MVC10A

Brands by name

Popular brands

Azbil MVC10A, User Manual

Search results

Summary of Contents for MVC10A

Reviews:

Related manuals for MVC10A

Brands by name

Popular brands