Power & Low Battery
Sound Lights
*LED
Adapter:
-Store this product out of the reach of babies (at least 3 feets (0.9 m)
away from the crib). A strap wound around the baby’s neck may result in
asphyxiation. Use a safety clip to clamp the power cord and keep it out
of baby’s reach. Do not use other extension cords. Only use the power
adapter provided.
-Do not touch the exposed part if the adapter is connected with power.
-Test regularly before initial use or when change the position of camera.
-Avoid placing the product in humid place or contacting with liquid. (such as bathtub, sink, etc.)
-Do not apply heat to the product.(such as stoves, radiators, etc.)
-Using the product in ventilated place. Avoid placing it on sofas, cushions, beds or other places which
may block ventilation.
-The product only can be operated by adult. Do not allow baby to play with it. Tiny accessories are
contained, please be careful when unpack and install it.
THIS PRODUCT CAN NOT SUBSTITUE PARENT’S SUPERVISION
ON YOUR CHILD.
WARNING
× 1
× 2
× 3
INSTRUCTION MANUAL
Model- E622
Revised at 11/2020
KOEHOG E622 Video Baby Monitor
with 2.4 '' LCD Screen & Two Cameras
Get to know us at: www.koehog.com
Please read the following instructions and warnings carefully
Keep this instruction manual for the future.
For technical support see the FAQ page.
For adult use only.
Please charge the battery for at least 8 hours before
using the product.
Step 1:
Test reception first, put camera in a suitable place
that will provide you the best view of your baby in the crib
(Note: Do not hang up the camera firmly until initial
installation test is completed). Plug adapter into wall outlet
and turn on the camera.
Step 2:
Turn on monitor by pressing and holding
Power /
Menu “ ”
button for 5 seconds until “KOEHOG” shows up,
then video will show up on the screen immediately.
If video
does not show up, please refer to “TO PAIR MONITOR AND
CAMERA (ADD CAMERA)” at next page. If video shows up,
the initial installation test is completed, then you can set up
the camera according to the instruction below.
Set Up Camera:
Place camera on a flat surface, such as
wardrobe or shelf (Figure 1). Or hang it on the wall (Figure 2).
No matter wherever to place the camera, please make sure
to keep it away from the crib for at least 3 feet and all power
cords should be placed behind the camera properly. Then
adjust the angle of camera lens until the entire crib shows up
on the display, or adjust it to the best angle that you think to
watch your baby.
-Only use the recommended rechargeable battery. Please contact us if you need to change it.
For the contact list, please refer to the last page of the instruction.
-Please clean the battery compartment before using it.
-Avoid short circuits the power supply terminal.
-Remove the battery when you are not using it or when running out of power.
-Keep the battery away from children.
-Dispose of the empty battery properly.
BATTERY WARNING
SETUP & USE
The monitor and camera are paired before shipment. If it is unpaired for some reason, please refer
to the following steps:
Step 1:
Make sure the camera and monitor are in the same space.
Step 2:
3
Make sure the AC adapter is plugged into
camera and turn on the camera by
pressing Power On/Off Switch “ ”
button for 3 seconds.
3
Step 4:
Step 5:
Red LED flashs
1
2 3 4
Step 3:
No
Signal
2
1
3
1
2 3 4
4
The SCAN, SELECT, ADD, DELETE, VIEW CAMERA options are only available when
multiple cameras connected with the monitor. Order extra cameras by visiting
us at www.koehog.com or search “Axvue Baby monitor” on Amazon.
Press
FEATURES & COMPONENTS
Monitor:
Camera:
Keep the distance between sensor and
body
at least 0.6 inch for accurate
temperature result.
1. Night-Vision LED
2. Lens
3. Power Indicator
4. Microphone
5. Speaker
6. Power/Code
7. Temperature Sensor
8.
DC Jack
9. Wall Mounting Hole
1. LED*
2. Volume Up
3. Power/Video
4. Left
5. Menu/OK
6. Right
7. Talk Back/Zoom
8. Volume Down
9. Microphone
10. Speaker
11. Battery Compartment
12. Kickstand
13. DC Jack
0.6 in
Step 1:
Charge the battery for at least 6 hours before using portable / battery mode.
Step 2:
Make sure the adapter is plugged into camera.
Step 3:
The battery life can be up to 8 hours if it is fully charged.
Battery life will be shortened if recharging it continuously. Unplug the AC adapter when
you are not
using it for a long time.
Please charge the battery for
6~8 hours before using the product.
TO USE PORTABLE/BATTERY MODE
Step 1:
Place the monitor display in living room, bedroom or any place you want to watch your baby.
Use adapter to connect camera with electrical outlet.
Step 2:
Turn on monitor by pressing
POWER/VIDEO
“ ”
button for 3 seconds until
“
KOEHOG
” logo
or video shows up on the screen.
Step 3:
Press
POWER/VIDEO
“ ”
button to turn off the video if you only need to hear the voice.
Step 4:
Turn off the monitor completely by pressing and holding
POWER/VIDEO
“ ”
button for
3 seconds.
TO USE PLUGGED-IN MODE
TO PAIR MONITOR AND CAMERA (ADD CAMERA)
3 feet
3 feet
Figure 1
Figure 2
