× 3
keep the distance
between sensor and body
at least 0.6 inch for
accurate temperature
result
0.6 in
Step 3:
３
1. Night-Vision LED
2. Lens
3. Temperature Sensor
4. Microphone
5. Speaker
6. Power/Code
7. DC Jack
8. Wall Mounting Hole
Please charge the battery for at least 8 hours before
using the product.
Step 1:
Test reception first, put the camera in a suitable place that
will provide you the best view of your baby in the crib (Note: Do
not hang up the camera firmly until the initial installation test is
completed). Plug the adapter into the wall outlet and turn on the
camera.
Step 2:
Turn on the monitor by pressing and holding the Power /
Video“
” button for 5 seconds until “axvue” shows up, then
the video will show up on the screen immediately. If the video
does not show up, please refer to “TO PAIR MONITOR AND
CAMERA (ADD CAMERA)” on the next page. If the video shows
up, the initial installation test is completed, then you can set up
the camera according to the instruction below.
Set Up Camera:
Place the camera on a flat surface, such as a
wardrobe or shelf (Figure 1). Or hang it on the wall (Figure 2). No
matter wherever to place the camera, please make sure to keep it
away from the crib for at least 3 feet and all power cords should be
placed behind the camera properly. Then adjust the angle of the
camera lens until the entire crib shows up on the display, or adjust
it to the best angle that you think to watch your baby.
Turn on the monitor by pressing
and holding Power / Video
“
” button for 5 seconds.
Make sure the power adapter is plugged into
camera and turn on the camera by pressing
Power / Code“ ” button for 3 seconds.
Step 4:
Get to know us at: www.axvue.com
SETUP & USE
INSTRUCTION MANUAL
Model
- HD992
Revised at 9/2020
THIS PRODUCT CAN NOT SUBSTITUE PARENT’S SUPERVISION ON YOUR CHILD.
WARNING
WARNING
BATTERY WARNING
Step 2:
Adapters:
FEATURES & COMPONENTS
Camera:
× 1
× 2
Monitor:
3 feet
Figure 1
3 feet
Figure 2
TO USE PORTABLE / BATTERY MODE
Step 1:
Charge the battery for at least 8 hours before using portable / battery mode.
Step 2:
Make sure the adapter is plugged into the camera.
Step 3:
The battery life can be up to 15 hours if it is fully charged.
Battery life will be shortened if recharging it continuously. Unplug the power adapter when you are
not using it for a long time.
Please charge the battery for
6~
8 hours before using the product.
The monitor and camera are paired before shipment. If it is unpaired for some reason, please refer
to the following steps:
TO PAIR MONITOR AND CAMERA (ADD CAMERA)
Step 1:
Make sure the camera and monitor are in the same place.
OK
3
2
OK
5
1
6
OK
7
Power & Low Battery
Sound Lights
*LED
1. LED
2. MENU
3. Pan / Tilt
4. Motion Detection
5. Zoom / Talk Back (OK)
6. Volume
7. Brightness
8. Cam / Split
9. VOX
10. Microphone
11. Speaker
12. Battery Compartment
13. Kickstand
14. Power / Video
15. DC Jack
4
Step 1:
Place the monitor display in the living room, bedroom or any place you want to watch your
baby. Use an adapter to connect the camera with an electrical outlet.
Step 2:
Turn on the monitor by pressing the Power / Video“
” button for 5 seconds until axvue
logo or video shows up on the screen.
Step 3:
Press Power / Video“
” button to turn off the video if you only need to hear the voice.
Step 4:
Turn off the monitor completely by pressing and holding the
Power / Video“
” button
for 5 seconds.
TO USE PLUGGED-IN MODE
Please read the following instructions and warnings carefully
Keep this instruction manual for the future.
For technical support see the FAQ page.
For adult use only.
- Store this product out of the reach of babies (at least 3 feets (0.9 m) away from the crib). A strap
wound around the baby’s neck may result in asphyxiation. Use a safety clip to clamp the power cord
and keep it out of baby’s reach. Do not use other extension cords. Only use the power adapter
provided.
- Do not touch the exposed part if the adapter is connected with power.
- Test regularly before initial use or when change the position of camera.
- Avoid placing the product in humid place or contacting with liquid. (such as bathtub, sink, etc.)
- Do not apply heat to the product.(such as stoves, radiators, etc.)
- Using the product in ventilated place. Avoid placing it on sofas, cushions, beds or other places which
may block ventilation.
- The product only can be operated by adult. Do not allow baby to play with it. Tiny accessories are
contained, please be careful when unpack and install it.
- Only use the recommended rechargeable battery. Please contact us if you need to change it.
-
For the contact list, please refer to the last page of the instruction.
- Please clean the battery compartment before using it.
- Avoid short circuits the power supply terminal.
- Remove the battery when you are not using it or when running out of power.
- Keep the battery away from children.
- Dispose of the empty battery properly.
Asphyxiation Danger:
Store this product out of the reach of babies (at least 3 feet away from the
crib). A strap wound around the baby’s neck may result in asphyxiation. Use a safety clip to clamp the
power cord and keep it out of baby’s reach. Do not use other extension cords. Only use the power
adapter provided.
AXVUE HD992 VIDEO BABY MONITOR
WITH 5" HD LCD SCREEN & 2 CAMERAS
× 2
× 2
× 12
