SETUP & USE
( continued )
FCC INFORMATION
This device complies with part 15 of FCC Rules. Operation is subject to
the following two conditions: (1) The device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
CAUTION
Changes and modifications not expressly approved by AXVUE may void
the users authority to operate this equipment.
NOTE
This equipment has been tested and found to comply with the limits for a
Class B digital device,
Pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
CAUTION
1. To comply with the FCC RF exposure compliance requirement, a
separation distance of 20 cm must be maintained between the antenna
of this device and all persons.
2. This transmitter most not be co-located or operating in conjunction
with any other antenna or transmitter.
DO NOT EXPOSE TO RAIN OR MOISTURE
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
• Make sure you read this instruction carefully before using the product.
• Store this instruction safely for your future reference.
• Ensure that you read the “Warning” section of the product package and this instruction carefully.
• Use the product properly by following this instruction.
• Wipe the product by wet towel after you take it down from the wall.
• Avoid possible danger by following manufacturer’s instruction.
• Do not using the product in humid place or contact with liquid, like bathtub, hand washing sink, kitchen sink, laundry tub, humid
basement, swimming pool, etc.
• Ensure the product is installed in a flat place. Otherwise, it will cause serious personal injury and product damage when dropped.
• Only follow this instruction and use installation tools provided by the manufacturer to set up the product.
• The slots and holes on the product are used for ventilation, please ensure that it is not covered or blocked by other objects.
• Do not place the product on bed, sofa, rug or other similar places, it will block or cover the slots and holes on the product. Do not
place the product in a closed bookcase or shelf unless it has particular part for ventilation.
• This product should be connected with certain power supply unit, if you are not sure about the power supply system in your home,
please contact with your product dealer and local power supply company. Please refer to the operating instruction if you want to
operate the product in portable/battery mode or by connecting with other power supply sources.
• Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them,
paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
• An outside antenna system should not be located in the vicinity of overhead power lines or other electrical lines or power circuits, it will
cause interference for the signal transmission. When installing an outside antenna system, extremely attention should be paid to avoid
touching such power lines or circuits, otherwise, you will have possible danger of electrical shock.
• Do not overload wall outlet, extension cords or convenience receptacles, this can be cause a risk of fire or electrical shock.
• Do not insert any tiny objects into the product’s inside, it may touch dangerous voltage point or cause short-circuit, this can be cause
a risk of fire or electrical shock. Any kind of liquid spillage happens on the product should be avoid.
• Do not maintain the product by yourself as opening and removing the covering, this may expose you to dangerous voltage or other
hazards. Please contact with qualified service personnel for maintaining.
• Unplug the product from wall outlet and contact with qualified service personnel if you have problems as below:
- When the power-supply cord or plug has been damaged.
- If liquid has been spilled, or objects have fallen into the product.
- If the product has been exposed to rain or water.
- If the product didn’t operate normally by following the operating instructions, please only adjust those controls which are covered by
the operating instructions. An improper adjustment of other controls may result in product damage, it will also require extensive
work from qualified service personnel to restore the product to its normal operation mode.
- If the products has been dropped or damaged in any way, or when the product shows a distinct change in performance
- this indicated that the product need to be maintained.
• Replacement parts - When replacement parts are required, be sure the service technician has used replacement parts specified by
the manufacturer or its have the same characteristics as the original part. Unauthorized substitutions may result in fire, electrical
shock or other hazards.
• Safety Check - Upon completion of any service or repairs to this product, ask the service technician to run safety checks on the
product to confirm that it is in a proper operating condition.
• The product only can be mounted on the wall or ceiling as recommended by the manufacturer.
• The product should be kept away from heat sources, such as radiator, heat registers, stoves or other products (including amplifier)
which can produce heat.
AXVUE INC.
Revised at 12/2020
*Any updated or revised version please refer to axvue official website
.
AXVUE stands behind all of its products.
If you are not completely satisfied or have any questions,
please contact us at https://www.axvue.com
Favorite Features
IMPORTANT SAFETY INSTRUCTIONS
Connect with us:
732-A1080DU-0700
80°F
27°C
6
TO ADJUST TEMPERATURE UNIT
TO ADJUST TIME
°F
°C
1
°F °C
1
24
10:
PM 12
6
10:24PM
OK
5
OK
3
OK
7
OK
5
OK
3
OK
7
4
4
2
2
TO SET UP VOX—Video on Crying
VOX OFF
VOX 1
3
OK
VOX OFF
VOX 1
2
VOX 1
Note*:
Under VOX mode, screen turns off automatically and turns on only when a certain level of
sound is detected by camera: “3” for High Volume, “2” for Medium, “1” for Low.
6X DIGITAL ZOOM IN & OUT
The zoom option enables you to get a closer and clear view on screen. Press the Zoom/Talk Back “ ”
button for times to 6x zoom in the video on screen or return to the normal size.
TWO-WAY COMMUNICATION
Your baby is always eager to hear your voice when crying. Press and hold the Zoom/Talk Back “ ” button
on the monitor to activate two-way communication mode. When you see this icon “ ” shows up on the
screen, then you can talk with your baby. Release the button to end this mode.
NIGHT VISION
The infrared LEDs and the lens are used for night vision which will light up automatically after you turn off
the light. The image on the monitor will turn to black and white when camera is in a low-light or dark room.
SOUND LIGHT
The LED sound light bar on the top of the monitor will light up in red based on the level of baby’s sounds.
Louder sounds will activate more LEDs to light up.
VOLUME CONTROL
Turn up the volume to hear every little sound from your baby (like cooing), turn down the volume to
monitor louder sounds and crying from baby. Easily adjust to the volume level you want by pressing Volume
“ ” button, and then choose left “ ” or right “ ” to adjust.
BRIGHTNESS ADJUSTMENT
Screen brightness can be adjusted according to the light intensity of your room. Adjust lighter or darker
video image by using the brightness control function. Press the BRIGHTNES“ ” button at the right of
monitor, and then choose LEFT“ ” or RIGHT“ ” to adjust to the brightness you want.
VIDEO ON/OFF
To preserve battery life when monitor is not plugged into AC outlet, the screen will turn off by pressing
Power/Video “ ” button, under this pattern, monitor still can get audio and sound from camera detection.
Press Power/Video “ ” button again, screen will turn on to resume video & audio monitoring.
6X MAGNIFYING CANVAS MOVEMENT FUNCTION
2
1
1
TO USE MOTION TRACKING FUNCTION
Under motion detection mode, screen turns off automatically, it will light up and sound alarms if your baby
has any movement to be detected.
5
OK
1
ON
4
TO DELETE A CAMERA
Press and hold the TALK BACK“ ”
button on the monitor to activate
two-way communication mode.
Press &
hold
TO USE 2-WAY COMMUNICATION
1
4
6
DELELT CAM?
NO
YES
8
2
TO VIEW ONE CAMERA WITH FULL SCREEN ( SELECT CAMERA )
2
Note*
: Under this mode, any changes of camera setting (eg. Talk back, Motion detection, VOX level
setting, etc.) will only be available for Camera 1.
:
Under this mode, any changes of camera setting (eg. Talk back, Motion detection, VOX level
setting, etc.) will only be available for Camera 2.
TO VIEW TWO CAMERAS WITH SPLIT SCREEN
2
3
OK
9
OK
5
OK
7
OK
3
OK
3
OK
3
OK
3
1
2
1
1
