Axis P1445-LE-3 User Manual Download Page 11

Page: 11 / 65

AXIS P1445-LE-3 License Plate Verifier Kit

Get started

Example with one area of interest.

Note

For performance reasons, keep the area of interest as small as possible.

Select region

1. Go to

Settings

Image

2. In the

Region

drop-down list, select your region.

Adjust the image capture settings

1. Go to

Settings

Image

2. To change the resolution of captured images, go to

Resolution

3. To change the rotation of the captured image, go to

Image rotation

4. To change how you save your captured images, go to

Save full frame

License plate crop

saves only the license plate.

Vehicle crop

saves the entire captured vehicle.

Frame downsized 480x270

saves the entire image and reduces the resolution to 480x270.

Full frame

saves the entire image at full resolution.

Set up event storage

An event consists of the captured image, the license plate, the area of interest number, vehicle direction, access, and the date and time.

Summary of Contents for P1445-LE-3


































































Search results

Summary of Contents for P1445-LE-3

Reviews:

Related manuals for P1445-LE-3

Brands by name

Popular brands

Axis P1445-LE-3, User Manual

Search results

Summary of Contents for P1445-LE-3

Reviews:

Related manuals for P1445-LE-3

Brands by name

Popular brands