Axis ExCam XF Q1785 User Manual Download Page 31

Page: 31 / 34

AXIS Q17 Series

Specifications

•

Leveling assistant

– This function helps to ensure the camera is level. Press the button for about 3 seconds to start the

leveling assistant and press again to stop the leveling assistant. The buzzer signal assists leveling of the camera, see

Buzzer

signal for leveling assistant on page 30

. The camera is level when the buzzer beeps continuously.

Connectors

Network connector

RJ45 Ethernet connector with Power over Ethernet (PoE).

IDC connector

Use the insulation-displacement connector (IDC) to connect a network cable without an RJ45-connector.

Note

When using the IDC connector, connect a patch cable between the patch cable connector on the foot and the network
connector on the camera assembly.

1–8 IDC connectors
9

Patch cable connector

Pin assignment

Position

T586A

T586B

Blue and white

Blue

Orange and white

Green and white

Orange

Green

Green and white

Orange and white

Green

Orange

Brown and white

Brown

Audio connector

•

Audio in

– 3.5 mm input for a mono microphone, or a line-in mono signal (left channel is used from a stereo signal).

Audio input

Summary of Contents for ExCam XF Q1785



































Search results

Summary of Contents for ExCam XF Q1785

Reviews:

Related manuals for ExCam XF Q1785

Brands by name

Popular brands

Axis ExCam XF Q1785, User Manual

Search results

Summary of Contents for ExCam XF Q1785

Reviews:

Related manuals for ExCam XF Q1785

Brands by name

Popular brands