AWH Tanko RT Operating & Installation Instructions Manual Download Page 68 | Manualshive

Page: 68 / 132

AWH Tanko RT Operating & Installation Instructions Manual Download Page 68

ATEX Retractor System TANKO-RT/-RTS

58/121

Translation - Operating/installation instructions 2020/01

5 Installation

5.2.2

Installation Position

The installation position of the device can be freely selected.

If the device is not installed in a vertical position, the retractor systems must be held in
place/supported by suitable pipe clamps (see AWH catalog, “Pipes & Assembly Accessories” at

http://www.awh.eu

); this is recommended for stroke lengths greater than 250 mm.

The pipe clamp should be secured close to the compressed air connection at the rear end of
the pneumatic cylinder, otherwise there is a risk of damage to the pneumatic pipe.

Self-Draining

Figure 5.2-2: Self-Draining of the Device, Depending on the Installation Position

Self-draining OK

Self-draining

OK

Self-draining

not assured

Self-draining

not assured

Self-draining OK

Self-draining OK

«
...
66
67
68
69
70
...
»

Summary of Contents for Tanko RT





































































































































Reviews:

No comments