AWB OD200-IDU Operator'S Manual Download Page 68

Page: 68 / 114

VoIP Settings

7-2

SIP Account

From the VoIP SIP Account page, you can configure the basic SIP service
parameters for Phone 1 and Phone 2.

Figure 7-1 SIP Account Settings

Enable Proxy Outbound

– Enables the use of proxy servers in the local network to

forward SIP requests. (Default: Disabled)

Always Proxy Outbound

– Forces all SIP requests to be forwarded through local

proxy servers. (Default: Disabled)

Expire Time

– The time the OD200 waits for a response from a proxy server before

a VoIP call fails. (Range: 61-65535 seconds; Default: 3600 seconds)

User Name

– The SIP account user name.

Auth. User Name

– An alphanumeric string that uniquely identifies the user to the

SIP server.

Auth. Password

– An alphanumeric string that uniquely identifies the SIP user’s

permission rights.

Display Name

– The name that is displayed to the other party during a call.

Summary of Contents for OD200-IDU



















































































































Search results

Summary of Contents for OD200-IDU

Reviews:

Related manuals for OD200-IDU

Brands by name

Popular brands

AWB OD200-IDU, Operator'S Manual

Search results

Summary of Contents for OD200-IDU

Reviews:

Related manuals for OD200-IDU

Brands by name

Popular brands