Award MI930 User Manual Download Page 37

Page: 37 / 60

BIOS SETUP

MI930 User’s Manual

Integrated Peripherals

This section sets configurations for your hard disk and other integrated
peripherals. The first screen shows three main items for user to select.
Once an item selected, a submenu appears. Details follow.

Phoenix - AwardBIOS CMOS Setup Utility

Integrated Peripherals

Onboard Device

Press Enter

ITEM HELP

South OnChip IDE Device

Press Enter

Menu Level >

South OnChip PCI Device

Press Enter

SuperIO Device

Press Enter

Init Display First

Onboard

Surroundview

Disabled

OnChip USB Controller

Enabled

USB EHCI Controller

Enabled

OnChip USB KBC Controller

Enabled

USB Mouse Support

Enabled

IDE HDD Block Mode

Enabled

Phoenix - AwardBIOS CMOS Setup Utility

Onboard Device

Onboard Marvell PCIE NIC 1

Enabled

ITEM HELP

Onboard Marvell PCIE NIC 2

Enabled

Onboard LAN Boot ROM

Disabled

Menu Level >

Phoenix - AwardBIOS CMOS Setup Utility

South OnChip IDE Device

IDE DMA transfer access

Enabled

ITEM HELP

On-Chip IDE Channel0

Enabled

Primary Master PIO

Auto

Menu Level >

Primary Slave PIO

Auto

Primary Master UDMA

Auto

Primary Slave UDMA

Auto

Phoenix - AwardBIOS CMOS Setup Utility

South OnChip PCI Device

HD Azalia Audio

Auto

ITEM HELP

OnChip SATA Controller

Enabled

OnChip SATA Type

Native IDE

Menu Level >

SB600 Spread Spectrum

Enabled

Summary of Contents for MI930





























































Search results

Summary of Contents for MI930

Reviews:

Related manuals for MI930

Brands by name

Popular brands

Award MI930, User Manual

Search results

Summary of Contents for MI930

Reviews:

Related manuals for MI930

Brands by name

Popular brands