AVYCON AVK-TL91E4-1T User Manual Download Page 42

Page: 42 / 105

PTZ

DVR User Manual

PTZ

6.1 PTZ Control Interface Introduction

You can control the dome or PTZ which connects to the camera for PTZ control.

Click

on the tool bar at the bottom of the live preview window to go to the PTZ control

interface as shown below. You can select another dome or PTZ which connects to the camera
on the top right of the interface for PTZ control.

Introductions of the buttons on the bottom right of the interface:

Button

Meaning

Click

to rotate the dome. Click

to stop rotating the dome.

Click

to zoom in / out the camera image.

Click

to increase / decrease the focal length.

Click

to increase / decrease the iris of the dome.

Drag the slider to adjust the rotating speed of the dome.

Click

to start / stop recording.

Click

to hide / show the analog joystick.

Click it to return to the live preview interface.

Summary of Contents for AVK-TL91E4-1T










































































































Search results

Summary of Contents for AVK-TL91E4-1T

Reviews:

Related manuals for AVK-TL91E4-1T

Brands by name

Popular brands

AVYCON AVK-TL91E4-1T, User Manual

Search results

Summary of Contents for AVK-TL91E4-1T

Reviews:

Related manuals for AVK-TL91E4-1T

Brands by name

Popular brands