![background image](http://html1.mh-extra.com/html/avtech/erisstation-vcs702-wm/erisstation-vcs702-wm_quick-start-manual_3034392001.webp)
Quick start guide
Model: VCS702-WM
ErisStation
businessphones.v tech.com
Conference Phone
with Two Wireless Mics
Congratulations
on purchasing your new VTech product.
For support, shopping, and everything new at VTech, visit
our website at
http://businessphones.vtech.com
or call
(US)
1-800-595-9511
, (Canada)
1-800-267-7377
.
Install battery to the wireless mic
Risk of explosion! Batteries should not be exposed to
excessive heat such as bright sunshine or fire.
Use only the supplied battery.
Risque d’explosion! Le bloc-piles ne doit pas être exposé à
la chaleur excessive telle que la lumière du soleil ou au feu.
N’utilisez que la pile incluse.
•
•
•
•
1. Plug the battery connector securely into the socket inside
Plug the battery connector securely into the socket inside
the battery compartment. Insert the battery with the label
THIS SIDE UP
facing up onto the battery compartment.
2. Slide the battery door until it clicks into place.
3. Place the wireless mics into the charging cradles until
they are flush.
Register the wireless mic
You should register your new wireless mic to the base unit
following the instructions below.
To register the wireless mic
As part of this process, all existing, broken, or lost wireless
mics will be deregistered first. Then, the base unit will
re-register the two wireless mics that are placed into the
charging cradles.
Before registration, unplug the telephone line cord from the
wall jack to make sure there are no incoming calls during
registration.
Gather the two wireless mics that are to be registered,
and then place them into the charging cradles.
Enter
331734
on the base unit when it is not in use,
and then press
. The screen displays
Please place all
wireless mics
on cradle, then press ‘SELECT’
.
Make sure both wireless mics are on the charging
cradles, and then press
. The wireless mics enter the
deregistration mode, and the screen displays
Processing...
.
After deregistration is complete, registration starts.
The screen displays
Registering... 1 2
. The number
X
blinks while registering the X-th wireless mic. You hear a
confirmation tone when each wireless mic is registered.
When both wireless mics are registered, the base unit
displays
Registration done
.
1.
2.
3.
Charge the battery for 8 hours before use.
If the wireless mic unit becomes warm when the
battery is charging, it is normal.
•
•
After registration, plug the telephone line cord back into the
wall jack.
If registration fails, the base unit will display
Registration failed. Try again
and
returns to idle. You hear an error tone. Remove
the wireless mics from the charging cradles and
place them back in. Repeat steps 1 to 3 to try
the entire registration process again.
If the screen does not display
Registration
done
after step 3, repeat steps 1 to 3 to try the
entire registration process again.
All wireless mics should always be kept on the
charging cradles during the whole registration
process. Any wireless mic that is registered
before but not put into the charging cradle will be
deregistered after the above operations.
Status indicators on the wireless mics flash red
and green alternately during registration.
To cancel registration, press
. The base unit
displays
Registration cancelled
. If registration
is cancelled, some of the wireless mics may
be deregistered. To register them back to the
base unit, repeat steps 1 to 3 to try the entire
registration process again.
•
•
•
•
•
Specifications are subject to change without notice.
© 2015 for VTech Communications, Inc.
All rights reserved. 06/15. VCS702-WM_QSG_V1.0
Document order number: 96-010673-010-100
3