Avnet Xilinx Zynq 7Z045 Manual Download Page 19

Page: 19 / 36

Page 19

The following table contains the ZYNQ PL pin number assignments for the Flash interface.

Table 7

– Parallel Flash Pin Assignments

2.3.3

QSPI Flash Interface

The Zynq 7Z045 Mini-Module Plus Development Board utilizes two on-board Spansion multi-
bit (x4) SPI flash devices, part number

S25FL128SAGMFIR0

, to configure the Zynq PL quickly

using the QSPI configuration mode. The QSPI devices are connected to bank 500 of the 7Z045.
For PCI Express applications the QSPI interface must be used to configure the 7Z045 to insure
meeting the 200 ms PCI Express configuration time requirement.

Net Name

7Z045 Pin #

PFLASH_D0

L12

PFLASH_D1

H12

PFLASH_D2

L10

PFLASH_D3

K12

PFLASH_D4

J11

PFLASH_D5

K10

PFLASH_D6

J10

PFLASH_D7

PFLASH_D8

G10

PFLASH_D9

H11

PFLASH_D10

PFLASH_D11

PFLASH_D12

PFLASH_D13

PFLASH_D14

PFLASH_D15

PFLASH_CE#

B10

PFLASH_WE#

PFLASH_OE#

PFLASH_RST#

PFLASH_ADV#

PFLASH_WAIT

PFLASH_CLK

K11

Net Name

7Z045 Pin #

PFLASH_A1

PFLASH_A2

D10

PFLASH_A3

PFLASH_A4

PFLASH_A5

PFLASH_A6

A10

PFLASH_A7

G11

PFLASH_A8

PFLASH_A9

D11

PFLASH_A10

F10

PFLASH_A11

PFLASH_A12

E11

PFLASH_A13

PFLASH_A14

PFLASH_A15

PFLASH_A16

PFLASH_A17

E10

PFLASH_A18

PFLASH_A19

PFLASH_A20

PFLASH_A21

PFLASH_A22

PFLASH_A23

M10

PFLASH_A24

PFLASH_A25

PFLASH_A26

PFLASH_A27

M12

Summary of Contents for Xilinx Zynq 7Z045





































Search results

Summary of Contents for Xilinx Zynq 7Z045

Reviews:

Related manuals for Xilinx Zynq 7Z045

Brands by name

Popular brands

Avnet Xilinx Zynq 7Z045, Manual

Search results

Summary of Contents for Xilinx Zynq 7Z045

Reviews:

Related manuals for Xilinx Zynq 7Z045

Brands by name

Popular brands