manualshive.com logo in svg

AVM FRITZ!Box Fon WLAN, Installation And Operation Manual

Share
Download
AVM FRITZ!Box Fon WLAN Installation And Operation Manual Download Page 125

Call-back on Busy (CCBS)

FRITZ!Box Fon WLAN 7170 – 11 Configuration and Operation by Telephone

125

Call-back on Busy (CCBS)

When you dial a number and it is busy, enable this feature.
As soon as the line is free, your telephone rings for 20 sec-
onds, as it would for an external call. When you pick up your
handset, the number of desired party will be dialed automat-
ically.

This feature is supported for both external and internal con-
nections.

A maximum of five call-back requests can be enabled for
each extension at any given time.

To enable this feature, proceed as follows:

M

You have just dialed a number and now you hear
the busy signal.

5

If the call is not answered, within twenty seconds,
dial either the number “5”

or

Rs37r

the sequence shown at left.

Q

Wait for the acknowledgement tone.

O

Hang up the handset.

K

As soon as the subscriber you dialed hangs up,
your telephone will ring.

N

Pick up the handset. The subscriber’s number is
dialed again automatically.

Summary of Contents for FRITZ!Box Fon WLAN














































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands