manualshive.com logo in svg

AVM FRITZ!Box Fon WLAN, Installation And Operation Manual

Share
Download
AVM FRITZ!Box Fon WLAN Installation And Operation Manual Download Page 104

Configuring by Telephone

104

FRITZ!Box Fon WLAN 7170 – 11 Configuration and Operation by Telephone

11.2 Configuring by Telephone

Restoring Factory Settings

The FRITZ!Box Fon WLAN can be reset to its condition upon
delivery.

All settings you made in the FRITZ!Box Fon WLAN—including
the configured Internet connection—are then deleted.

After restoring factory settings, the FRITZ!Box Fon WLAN is re-
started.

Saving New Settings

In this section, saving refers to all current settings. It is not
necessary to save the configuration after each setting is
made. You may first configure all of your FRITZ!Box Fon
WLAN’s settings as desired, and then save them permanent-
ly.

Saving Permanently

Permanent saving cannot be reversed. However, you can re-
set the PBX to its factory settings or program it with different
settings.

r991s15901590s

resets FRITZ!Box Fon
WLAN to its condition up-
on delivery.

N

Pick up the handset.

r91ss

Save all settings made to your
FRITZ!Box Fon WLAN permanently by
dialing the sequence shown at left.

O

Hang up the handset.

Summary of Contents for FRITZ!Box Fon WLAN














































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands