manualshive.com logo in svg

AVL 415SE, Maintenance Manual, Page: 24 / 50

Share
Download
AVL 415SE Maintenance Manual Download Page 24

Maintenance 

24

AVL 415SE Smoke Meter — Maintenance Guide

1.

Carry out a reference measurement with a "new" line, if it seems to be nec-
essary.

2.

Replace the sampling lines (Viton hoses) regularly.

Recommended replacement intervals: every 1 000 … 2 000 operating hours.

The material number depends on the length of the sampling line

2.3.5 

Suction Unit

Clamp piece 
tracks

1.

Check the friction conditions in the clamp piece tracks.

2.

Remove the hose from the upper clamp piece

3.

Release the clamping lever and open it completely.

4.

Check the clamp piece tracks for easy movement.

5.

If necessary, lubricate track (ex-works: Teflon lubricant spray - part number 
HS0058, Teflon lubricant oil - part number HS0064, or Lubricant grease 
OKS 260 - part number HS0071)

Fig. 7  Sampling line

Information

Heavier soot deposits can occur when using new sampling lines for the first time 
straight from the factory and this can also reduce the recorded FSN values.

The lower the measurement values, the higher, the requirement for repeatability, 
and reproducibility.

The greater is the influence of the soiling along the entire sampling path.

Fig. 8  View of the suction unit in the device

Information

Remember the hose clip when disconnecting and reconnecting the hose.

Summary of Contents for 415SE



















































Reviews:

No comments