manualshive.com logo in svg

AvL Technologies AAQ CIP, Setup & Operation Manual

Share
Download
AvL Technologies AAQ CIP Setup & Operation Manual Download Page 39

 

AAQ Controller Interface Panel (CIP)

 

 

 

 

 

38 

 

5.6.

 

Verifying Current Functionality 

A message box of the current functionality details will be shown when button is pressed: 

 

 

Figure 62 - Verify Switch/ Router Configuration 

These status items are defined in the following table: 

Label 

Definition 

Current Router Setup: 

Network Switch / Network Router 

WAN Controller DHCP Enabled: 

Flag to indicate if the router (controller port) is set to be 
a DHCP client 

WAN Controller IP Address: 

Current WAN IP address of the CIP (controller port) 

WAN Controller Subnet Mask: 

Current WAN Subnet of the CIP (controller port) 

WAN Controller Gateway 1: 

Current WAN Gateway location 

WAN Controller Gateway 2: 

Current Backup WAN Gateway location 

WAN Controller DNS: 

Current WAN DNS location 

WAN Power Cycle DHCP 
Enabled: 

Flag to indicate if the router (remote power cycle port) is 
set to be a DHCP client (Currently Unsupported) 

WAN Power Cycle IP Address: 

Current WAN IP address of the CIP (remote power cycle 

port) 

WAN Power Cycle Subnet Mask: 

Current WAN Subnet of the CIP (remote power cycle 

port) 

Summary of Contents for AAQ CIP










































Reviews:

No comments

Brands by name

Popular brands

Load more brands