AVL DITEST ADS 340 User Manual Download Page 52 | Manualshive

Page: 52 / 112

AVL DITEST ADS 340 User Manual Download Page 52

Maintenance

AVL DiTEST ADS 340

6-2

User Manual

6.2

Regular maintenance

6.2.1 Changing the vacuum pump oil

Once the vacuum pump has reached 500 operating hours, or at least once a year, the vacuum
pump oil needs to be changed. The AVL DiTEST ADS 340 points out the required vacuum pump
oil change to you.

1. Select

Maintenance

│Vacuum pump oil

.

2.

The following is being displayed:

- Time since last oil regeneration
- Remaining time for oil regeneration
- Time since last oil change
- Remaining time for oil change
- Start the regeneration of the vacuum pump oil
- Reset counter for vacuum pump oil (for vacuum pump oil exchange)

3. Switch off the ADS 340 and additionally disconnect the mains plug.

4. Switch off the AVL DiTEST ADS 340 and additionally disconnect the mains plug.

5. Unscrew the Allen screw to drain the oil (a).

The oil drains into the extensible oil collector tank (b).

Fig. 6-1

6. Refit the Allen screw (c).

7. Empty the oil collector tank (b).

When it comes to dispose of the vacuum pump oil, please mind the current legislation
in your country.

b

a

«
...
50
51
52
53
54
...
»

Summary of Contents for ADS 340

















































































































Reviews:

No comments