background image

Accessing ACM Embedded Controller Application

for the First Time

After the controller has been installed, you need to access the ACM Embedded Controller application to

complete the system configuration.

You can access the application by using the controller hostname or virtual port.

By Virtual Port

By default, every controller can be accessed from this IP address:

169.254.242.121

To perform this procedure, you must use a Windows computer with a web browser and a network port.

1. Disconnect the computer from the network.

2. Connect the computer to the controller using an Ethernet cable.

3. On your computer, open command prompt.
4. Enter

ipconfig/renew

Wait for DHCP to timeout (approximately 60 seconds). The computer will acquire a 169.254.x.x address.

5. Open a web browser and enter this address:

169.254.242.121

The controller is now accessible through this virtual port.

6. Enter your login for the application.

The default username and password is

admin

.

By Host Name

To access the ACM Embedded Controller application by this method, your DHCP server must support hostname

access and only have one controller in the local area network (LAN).

1. Make sure the controller has a LAN connection.

2. Power the controller and wait 60 seconds for the controller to start up.

3. In a web browser, enter this address:

https://acm-ec.

γ]Rcf^aY Q^\MW]δ

For example:

https://acm-ec.example.lan

The controller is now accessible through this URL.

4. Enter your login for the application.

The default username and password is

admin

.

See the

24? 6\ORQQRQ 4^]ca^ZZRa ;]bcMZZMcW^] 8dWQR

or the

24? 6\ORQQRQ 4^]ca^ZZRa GbRa 8dWQR

for more

detail.

20

Accessing ACM Embedded Controller Application for the First Time

Summary of Contents for AC-HID-LSP-ACMEC-KIT4























Reviews: