manualshive.com logo in svg

Avidyne Entegra EX5000, Installation Manual

Share
Download
Avidyne Entegra EX5000 Installation Manual Download Page 74

EX5000 Release 8.2.2 Installation Manual  

P/N 600-00073-001 Rev 02 

- 74 - 

5.12.3  XM Broadcast Datalink and FIS-B Checkout 

XM Broadcast Datalink Checkout 

To check the XM Broadcast Datalink Installation: 

1. 

Power up the MFD and Broadcast Datalink Receiver and select the Trip Page.  

2. 

From the Trip Page, press 

Display

 to view Broadcast Status (down pointing arrow). If the 

MFD reports a Receiver ID or Serial Number, the receiver is communicating with the MFD 
and the RS-232 wiring is correct. 

3. 

Position the aircraft in an area open to the sky.  

4. 

Power up the MFD and Broadcast Datalink Receiver and select the Trip Page.  

5. 

Check the Signal Quality, as displayed on the lower half of the Trip Page. 

Good

—Confirms the receiver is detecting the satellite signals. 

Marginal 

or 

Weak

—May require repositioning the aircraft to better location.  

None

—Indicates a bad antenna, cable, connection or receiver. 

For more information, see the 

XMD076 XM Receiver Installation Manual and Activation Instructions 

from Heads Up Technologies or contact Heads Up Technologies at 

[email protected]

 or (972) 

407-1131.  

Note:  

If Broadcast Datalink does not connect because the XM trial period has expired, call Heads 
Up Technologies at (972) 407-1131 to activate the account for testing. For information about 
customer activation, see the 

EX5000 Multi-Function Display Pilot’s Guide

.    

FIS-B Checkout 

To check the XM Broadcast Datalink Installation: 

1. 

 

After Setup is complete boot the MFD into flight mode and go to to the Aux page.  Verify the 
following message is displayed: “FIS-B Receiver is Operating Normally”. 

After restarting the MFD, either of the following messages may appear in the message bar on any 
page and in the message list on the Aux or Setup Page. 

Table 25: Broadcast Datalink and FIS-B Messages 

Message 

Meaning 

Broadcast is Operating Normally 

Verifies that the MFD is communicating with the Broadcast 
Datalink Receiver 

FIS-B Receiver is Operating Normally 

Verifies that the MFD is communicating with the Broadcast 
Datalink Receiver 

Broadcast is Not Communicating. (After 5 minutes of 
no communication). 

The MFD is not communicating with the Broadcast 
Datalink Receiver. Check power and signal wiring. 

FIS-B Receiver is Not Communicating. (After 5 minutes 
of no communication). 

The MFD is not communicating with the FIS-B Receiver. 
Check power and signal wiring. 

 

Make a note of the Receiver ID for the aircraft owner, who will need it to begin Broadcast Datalink 
service. 

To finish the checkout process, see Section 6.6 XM Broadcast Datalink Satellite Reception 
Confirmation. 

Summary of Contents for Entegra EX5000



















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands