manualshive.com logo in svg

Avidyne Entegra EX5000, Installation Manual, Page: 30 / 114

Share
Download
Avidyne Entegra EX5000 Installation Manual Download Page 30

EX5000 Release 8.2.2 Installation Manual  

P/N 600-00073-001 Rev 02 

- 30 - 

5.  MFD Feature Setup and Checkout 

5.1  Preliminary Test 

  Power up the MFD for post installation evaluation and configuration. To do so: 

1. 

 

Turn on the MFD by applying power to the aircraft electrical bus supplying the MFD. 

Note:

  Read the appropriate 

Pilot’s Guide 

for explanations of various functions. 

2. 

 

The green LED control lights behind all the front panel controls should light up. 

3. 

 

After the initial power up, the software will load and go through several checks. During this startup 
sequence the screen displays the text “Initializing-Please Wait...”. 

4. 

 

The startup sequence is finished when the “Press any bezel key to Continue...” message 
displays. 

 

Figure 6: EX5000 Landscape Front View 

5.2  Optional MFD Function Activation Utilities 

Avidyne provides the ability to install certain optional functionality using single-use activation utility 
disks. This section describes the installation procedure for these utilities. 

The Activation Utilities are available for use only by avionics repair facilities performing MFD 
installations, MFD software upgrades, and MFD function activation on installed MFD software.  

  To activate the TAWS, and Broadcast Datalink MFD features: 

1. 

 

Obtain the Activation Utility disk for each feature you want to install from Avidyne or an authorized 
aircraft manufacturer. Be sure to specify the software part number of the MFD for which you want 
to activate a feature.  

•

 

MFD Single-Use TAWS Activation Utility

—This utility activates the MFD TAWS function. 

This utility is for use in FAA-approved aircraft repair stations only.  

•

 

MFD Single-Use Broadcast Activation Utility

—This utility activates the MFD Broadcast 

Datalink function. This utility is for use in FAA-approved aircraft repair stations only.  

These utility disks can be run only once to activate a single function on an MFD. After a single 
use they will not run on an MFD.  

Summary of Contents for Entegra EX5000



















































































































Reviews:

No comments