background image

 MADI-192 MADI Option Card Installation Guide 1

MADI-192 MADI Option Card Installation Guide

The MADI-192 MADI Option Card is a high-channel-count 
MADI audio interface card for Avid

®

 VENUE | S6L systems. 

MADI-192 MADI Option cards are installed in E6L engines. 

• Up to four MADI Option cards can be installed in an 

E6L-192 or E6L-144 engine.

• Up to two MADI Option cards can be installed in an 

E6L-112 engine. 

For information on supported Option cards, visit: 

https://www.avid.com/products/venue-s6l-system

This guide shows how to install a MADI-192 MADI Option Card 
into an E6L. 

Required Materials

• MADI-192 MADI Option Card

• Phillips #1 screwdriver (not included)

• Anti-Static wrist strap (not included)

• Foam or other padded surface to place the card on (not in-

cluded)

Installing a MADI-192 MADI Card

Installing a MADI-192 MADI Option card in E6L consists of the 
following steps:

• Removing the E6L engine core

• Installing the card

• Replacing hardware

• Confirming Installation

Removing the E6L Engine Core

E6L Option cards are installed in the E6L engine core, which 
slides out of the E6L chassis. 

To remove the E6L engine core:

1

Put on your anti-static wrist band and configure according to 
its instructions.

2

Shut down your system, and disconnect any cables connected 
to your E6L engine.

3

Place your E6L on a table or other flat surface that provides 
enough room for the E6L engine core to be removed comfort-
ably. Make sure your surface is clear of any debris.

4

On the back of the E6L, loosen the four thumbscrews that se-
cure the core to the engine chassis.

5

Simultaneously pull the two bottom thumbscrews outward so 
the latches they are attached to are fully extended, as shown in 
Figure 2.

6

Using the handle, slowly slide the core partially out, locate the 
interior catch on the right side of the tray, and press it to release 
the core from the chassis.

Figure 1. Four thumbscrews on the back of the E6L

Figure 2. Latches fully extended

Figure 3. Location of the interior catch

© 2018 Avid Technology, Inc

 9320-70100-00 REV B

Summary of Contents for MADI-192 MADI







Reviews: