manualshive.com logo in svg

Avid Technology Digidesign USD, User Manual, Page: 33 / 96

Share
Download
Avid Technology Digidesign USD User Manual Download Page 33

Chapter 4: Using the USD

29

About Remote-Only Mode 

(USD Setup Only)

When the default Remote-Only Mode 
(Front Panel Lockout) is enabled in the 
USD Setup Preferences window, none of 
the USD front panel switches will be oper-
ational. The Remote Only LED will be lit.

To exit Remote-Only mode from the front 
panel:

■

Simultaneously press and hold down the 

Clock Reference, Positional Reference, and 
Frame Rate front panel switches.

This will disengage the USD from Remote-
Only mode. This is useful when the host 
computer is not easily accessible to over-
ride Remote-Only Mode.

✽

Pro Tools USD controls always provide ac-

cess to most USD parameters.

Using the Front Panel 
Generator/Parameter Switches

The Generator/Parameter Controls are la-
belled SET, DOWN, UP, and 
RUN/STOP/CLEAR. In addition to their pri-
mary generator functions, these switches 
provide front panel access to most USD pa-
rameters. 

Features Not Accessible from the USD’s Front 
Panel Controls

The front panel provides access to all USD 
features except the following (which can be 
controlled using Pro Tools or USD Setup): 
• Remote-Only Mode/Front Panel Lockout
• Firmware update

• Changing Window Burn Size, Vertical 

Position, Horizontal Position, and Color

• GPI (General Purpose Interface) func-

tions

• Choosing between Video In or Video Ref 

In connector for the Clock Reference 
source

• Variable Speed Offset (VSO) 

For a listing of available parameters, refer to 
“USD Controls in Pro Tools, USD Setup, 
and the Front Panel” on page 28.

Set

The SET switch has three primary func-
tions:

When time code is displayed  

Pressing Set 

once changes the Display from time code to 
parameter names. 

When a parameter name is visible  

Pressing 

Set once will change the Display to show 
parameter values. 

When a parameter value is visible  

Pressing 

Set once will set that parameter value, and 
will return the Display to time code. 

Down and Up

These switches scroll through parameter 
names and values (whichever is currently 
displayed):

Generator/Parameter Switches

44.1 kHz
48 kHz
PULL UP
PULL DOWN

POSIT

SET

DOWN

UP

RUN/STOP

CLEAR

Summary of Contents for Digidesign USD

































































































Reviews:

No comments