AVG EZTouch I/O Jr. Manual Download

Page: 4 / 52

EZTouch I/O

Jr.

4 / 52

Product Overview

Thank You for using AVG Automation's latest offering, the

EZTouch I/O

Jr.

- a compact 4”

TouchPanel integrated with a PLC (programmable logic controller).

This guide covers

information on the installation, wiring and specifications of the

EZTouch I/O

Jr. It also outlines

the troubleshooting and maintenance of an existing setup. The

EZTouch I/O

Jr. is a 4”

TouchPanel interface available with built-in 22 I/O or 28 I/O options. It is also available with

Ethernet option for programming and Modbus TCP/IP for instructions.

All the TouchPLCs use ladder logic for programming and share the same programming

environment. The ladder logic developed for one model can be used with other models by

changing the target device. The software used to program the

EZTouch I/O

Jr. is: EZ

Touch

Editor.

Summary of Contents for EZTouch I/O Jr.




















































Search results

Summary of Contents for EZTouch I/O Jr.

Reviews:

Related manuals for EZTouch I/O Jr.

Brands by name

Popular brands

AVG EZTouch I/O Jr., Manual

Search results

Summary of Contents for EZTouch I/O Jr.

Reviews:

Related manuals for EZTouch I/O Jr.

Brands by name

Popular brands