manualshive.com logo in svg

Aventics Marex ECS, Assembly Instructions Manual, Page: 15 / 60

Share
Download
Aventics Marex ECS Assembly Instructions Manual Download Page 15

About this product

14

AVENTICS

 | ECS Actuator | R417002911–BDL–001–AA

5

About this product

5.1

Performance description

The Marex ECS Actuator is used to set mechanically the engine 
speed and transmission direction of ship propulsion systems. It 
receives control commands from the Marex ECS Control Unit via 
the PROPULSION cable. The electric signals from the control 
unit are converted into motion of the actuator’s lever. The lever 
operates a push/pull cable which acts on throttle and gearbox. 
A teach-in-function is provided to store lever positions for 
defined engine speeds and gear box settings within a lever 
travel of 76 mm. 
In addition, the lever of the Marex ECS Actuator can be used as 
an emergency handle. 
The Marex ECS Actuator is designed for the operation with 
Marex ECS. Depending on the software some of the functions 
which are described in these assembly instructions may not be 
supported. Refer to the operating instructions of the complete 
system for the available functions before starting Marex ECS up 
in order to prevent operating errors. 

5.2

Product description

Two versions of the Marex ECS Actuator are available: 
R417002894 for 12 V DC-systems
R417002895 for 24 V DC-systems

5.2.1 Characteristics and features 

W

Body and lever made of die-cast aluminum, anodized

W

Stainless steel cover

W

All parts protected against water ingress (protection type 
IP65)

W

Switches and LEDs under transparent protective cover

Summary of Contents for Marex ECS





























































Reviews:

No comments