manualshive.com logo in svg

Avaya W310, Command Reference Manual, Page: 147 / 440

Share
Download
Avaya W310 Command Reference Manual Download Page 147

Chapter 8

Avaya W310 Command Reference Guide

131

To restore the default value for short retry limit:

short-slot-time-implemented

User level: privileged, supervisor.

Command Mode: Radio card, Template

Use the 

short-slot-time-implemented

 command to enable or disable the Short 

Slot Time option. The short-slot-time option is used with 802.11g radio cards only and 
allows you to maximize throughput. Radio cards in a mixed mode (such as 802.11b/g) 
cannot use the short slot time. The default is disabled.

Use the [no] form of this command to reset the short slot time to its default.

Syntax:

The syntax for this command is:

[no] short-slot-time-implemented <active | not-active>

Message:

After this command is initiated, the LAP must reboot for any change to this setting to take 
effect. The following message displays after you initiate this command:

This command will reboot the LAP(s). Do you want to continue (Y/N)?

•

Type 

Y

 to reboot the LAP.

•

Type 

N

 to cancel the reboot. The change in this setting will not take effect. 

W310-1 (super/LAP lobby/802.11g first-slot)# 

no short-

retry-limit

This command will reboot the LAP(s) - do you want to 

continue? (Y/N)

Syntax

Description

<active>

Enables the short slot time option for the 802.11g interface.

<not-active>

Disables the short slot time option for the 802.11g interface.

Summary of Contents for W310

























































































































































































































































































































































































































































Reviews:

No comments