Avaya QuesCom 400 Installation And Commissioning Manual Download

Page: 65 / 116

Calling party option

Description

Use this option to ignore the Calling Party
information. This option is used for TUI, AA,
MINIBAR, ROOMSTATUS, XPRESS
MESSAGE, and SETAWU call flows.
This option is available only if you selected
Advanced Setting.

Configuring the PMS setting

About this task

Configure the Property Management System (PMS) settings for the Hotel PMS interface.

Important:

Obtain the required information from the Hotel PMS representative and configure only the
options specified.

Procedure

1. On the

Web Configuration

main navigation bar, select

System Configuration

2. In the

System Configuration

navigation, select

PMS Setting

3. In the

PMS Setting

window, in the

IP Setting

section, click

Edit

to configure the

required options.

4. Type the required values for

PMS IP

and

Port No

For PMS IP, type the ELAN IP address.

5. Click

Update

to save your changes.

6. In the

PMS Setting

section, for the

PMS Type

select either

CS1000

Intuity

Lodging

Variable Definitions

Variable

Value

PMS IP

The PMS IP (ELAN) address.

Port No.

The PMS port number.

PMS Type

Select either CS1000 or Intuity Lodging .

Server configuration procedures

Avaya Hospitality Messaging Server 400 Installation and Commissioning

March 2012 65

Summary of Contents for QuesCom 400





















































































































Search results

Summary of Contents for QuesCom 400

Reviews:

Related manuals for QuesCom 400

Brands by name

Popular brands

Avaya QuesCom 400, Installation And Commissioning Manual

Search results

Summary of Contents for QuesCom 400

Reviews:

Related manuals for QuesCom 400

Brands by name

Popular brands