Avaya QuesCom 400 Installation And Commissioning Manual Download

Page: 48 / 116

Procedure

1. Slide the cover forward, and ensure that all the tabs on the front, rear, and side of

the cover engage the chassis correctly.

2. Close the fan door and slide the cover release latches back to lock the cover in

place.

3. Tighten the thumbscrew on the back of the server.

Installing the HMS 400 server

About this task

Install the HMS 400 server.

Prerequisites:

• Ensure the chosen location meets the requirements defined in

Site preparation checklist

page 13.

Procedure

Install the HMS 400 server in the 19–inch equipment rack according the instructions
provided with your server.

Connecting peripherals to the HMS 400 server

About this task

Connect the monitor, keyboard, and mouse to the HMS 400 server.

Caution:

Risk of system failure

Install and use only Avaya-approved peripheral devices. To prevent system failure, install
and use only Avaya-approved devices.

Procedure

1. Place the monitor, keyboard, and mouse in the same location as the server.

2. Plug the keyboard and mouse into the appropriate USB connectors on the front

panel of the server.

HMS 400 hardware installation

48 Avaya Hospitality Messaging Server 400 Installation and Commissioning

March 2012

Comments? [email protected]

Summary of Contents for QuesCom 400





















































































































Search results

Summary of Contents for QuesCom 400

Reviews:

Related manuals for QuesCom 400

Brands by name

Popular brands

Avaya QuesCom 400, Installation And Commissioning Manual

Search results

Summary of Contents for QuesCom 400

Reviews:

Related manuals for QuesCom 400

Brands by name

Popular brands