manualshive.com logo in svg

Avaya programming and use, Installation And Use Manual, Page: 62 / 468

Share
Download
Avaya programming and use Installation And Use Manual Download Page 62

PARTNER

®

 Advanced Communications System Installation, Programming, and Use

The 1600 DSL Module

2-30

4.

Do one of the following:

■

If you have the SDSL set for ATM, select the RFC 1483 port for the voice PVC (get this 
from the service provider).

■

If you have the SDSL set for Frame Relay, select the RFC 1490 port for the voice DLCI 
(get this from the service provider).

5.

Type the IP address of the voice PVC/DLCI, and press Enter.

6.

Press Esc to return to the Main Menu.

Router Configuration for Data

2

Follow these steps to configure the data PVC for the 1600 DSL module for any gateway:

1.

Select “2. Configure IP Router” from the Main Menu.

2.

Select “C. Configure Port IP Address” from the Router Configuration Menu.

3.

Select “1. SDSL” from the Available Interfaces list.

4.

Do one of the following:

■

If you have the SDSL set for ATM, select the RFC 1483 port for the data PVC. For a 
CopperCom or Jetstream gateway, only one RFC 1483 port appears; for a PathStar 
gateway, you must get the number of the port from the service provider.

■

If you have the SDSL set for Frame Relay, select the RFC 1490 port for the voice DLCI. 
For a CopperCom or Jetstream gateway, only one RFC 1490 port appears; for a PathStar 
gateway, you must get the number of the port from the service provider.

5.

Type the IP address of the data PVC/DLCI, and press Enter.

6.

Press Esc to return to the Main Menu.

LAN Configuration

2

Follow these steps to configure the LAN for the 1600 DSL module:

1.

Select “2. Configure IP Router” from the Main Menu.

2.

Select “C. Configure Port IP Address” from the Router Configuration Menu.

3.

Select “2. 10/100BaseT Ethernet” from the Available Interfaces list.

4.

Type the port number of the IP interface, and press Enter.

5.

Type the customer’s LAN’s IP address at the new IP address prompt, and press Enter.

6.

Type the customer’s subnet mask address at the subnet mask prompt, and press Enter.

7.

Type “N” at the “Select priority Normal/High” prompt.

8.

Type “Y” at the “Save new IP Information?” prompt.

9.

Select “S. Add/Remove a Static Route” from the Router Configuration Menu.

10. Select “F. Add/Change the Default Route” from the Router Modification Menu.

Summary of Contents for programming and use





















































































































































































































































































































































































































































































Reviews:

No comments