manualshive.com logo in svg

Avaya programming and use, Installation And Use Manual, Page: 139 / 468

Share
Download
Avaya programming and use Installation And Use Manual Download Page 139

Programming System Options

Hold Disconnect Time (#203)

4-41

5.

Do one of the following:

■

To assign or unassign another extension, press 

n

 or 

p

 until the extension 

number appears on the display. Then repeat Step 4.

■

To program another group, press 

N

 + 

P

 and enter a new group 

number. Then repeat Steps 3 and 4.

6.

Select another procedure, or exit programming mode.

Hold Disconnect Time (#203) 

4

Use this feature to change the hold disconnect time for an outside line (this feature is not available 
for the Hong Kong Release 3.0 version). When a caller on hold hangs up, the local telephone 
company may send a special signal to the system to free the line. Different telephone companies 
use different length signals. The length of the signal is called the hold disconnect time. If you place 
a call on hold and the caller hangs up, but the call does not disconnect within a minute after the 
caller hangs up, the hold disconnect time is probably set too high, or set at No Detection.

Considerations

4

■

If the telephone company does not send a signal, keep the hold disconnect time set to 450 
msec, the factory setting. The user must disconnect a held call manually by retrieving the call 
and then hanging it up.

■

Shorten the hold disconnect time only if abandoned calls on hold do not disconnect.

■

Lengthen the hold disconnect time only if calls are being disconnected prematurely.

■

Using Set administration, you can program and view the hold disconnect time for analog lines 
only. You must use the PARTNER ACS R6.0 PC Administration software to program and view 
the hold disconnect time for lines on the T1 module. 

■

The range of values for the hold disconnect time is different for lines on the T1 module. For 
these lines, the values are No Detection, or 10 to 2400 msec. in 20 msec. increments. The 
default setting is 300 msec. See the PARTNER ACS R6.0 PC Administration software for 
more information.

Programming

4

To change the hold disconnect time for a non-T1 line:

1.

Press 

f00ss#203

 at extension 10 or 11.

2.

At the 

Line

: prompt, enter the two-digit number of the line for which you are adjusting the hold 

disconnect time.

The current hold disconnect time for the line number you specified is displayed. For example, 
if line 1 is set to the factory setting, 

09-450

 

msec

 appears on the display. 

Summary of Contents for programming and use





















































































































































































































































































































































































































































































Reviews:

No comments