Avaya P332GT-ML Installation And Configuration Manual Download Page 141 | Manualshive

Page: 141 / 150

background image

Avaya P332GT

-ML User’s Guide

127

Chapter 14

Troubleshooting the Installation

Troubleshooting the Installation

This section will allow you to perform basic troubleshooting of the installation. If
you are unable to solve the problem after following the procedures in this chapter,
please contact Avaya Technical Support. Refer to “How to Contact Us“for full
details.

Table 14.1

Troubleshooting

Problem/Cause

Suggested Solution

Switch does not power up

• AC power cord not inserted

or faulty

• Check that the AC power cord is

inserted correctly

• Replace the power cord

If the cord is inserted correctly, check that the AC power source is working by
connecting a different device in place of the P3330.
• If that device works, refer to the next step.
• If that device does not work, check the AC power

• P3330 AC power supply not

functioning

• Use an optional BUPS (Backup Power

Supply)

• Contact your local Avaya distributor.

The

power supply is not user-replaceable.

Stacking not functioning

• X330-STK modules not

inserted correctly
(LEDs on stacking module
do not light)

• Check that modules are installed

correctly

• Octaplane™ cables not

installed correctly
(LEDs on stacking module
do not light)

• Check that the cables are inserted

correctly

• Check that there are no cross-corrections

«
...
139
140
141
142
143
...
»

Summary of Contents for P332GT-ML























































































































































Reviews:

No comments

Related manuals for P332GT-ML

Brand: B&K Pages: 2

Brand: B&B Electronics Pages: 45

Brand: ifs Pages: 352

Temperature SWICHGAGE SPL

Brand: Murphy Pages: 4

Brand: LEGRAND Pages: 2

MyPower S2300-28TC-AC

Brand: Maipu Pages: 31

Brand: protech Pages: 4

Brand: Grozone Control Pages: 20

Brand: ATEN Pages: 26

pro-trim PT1000

Brand: Seastar Solutions Pages: 2

Brand: Thinklogical Pages: 17

Brand: NETGEAR Pages: 8

Brand: TP-Link Pages: 34

IMI SENSORS EX686B77

Brand: PCB Piezotronics Pages: 63

Power Switch G0021

Brand: G-Force Pages: 2

Brand: MiLAN Pages: 12

Brand: GORMAN-RUPP PUMPS Pages: 4

Brand: e+p Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands