Avaya one-X Deskphone SIP 9620C Installation Manual Download Page 48 | Manualshive

Page: 48 / 99

Avaya one-X Deskphone SIP 9620C Installation Manual Download Page 48

H323 Telephone Installation

Page 48

Issue 23e (Friday, February 15, 2019)

IP Office™ Platform 11.0

Comments on this document? [email protected]

2.7 Static Address Installation

Static addressing is only necessary when a DHCP server is unavailable or not desired. For ease of maintenance and
installation, it is strongly recommended that a DHCP server used and that static addressing is avoided. Following any boot
file upgrade of the phone's firmware, static address information may require reinstallation.

1600 Series Phones

1. Follow the steps in

Phone Connection

until

DHCP

is shown on the phone display. Press * at this point to switch

the phone to static address installation.

2. The phone will display a sequence of settings and the existing value for each of those settings. To accept the

current value, press # or enter a value and then press #.

3. The settings shown for static address installation are:

·

Phone =

This is the phone's IP address. To accept the current value, press

#

or enter a value and then press

#

. If

entering a new value, press the

*

key to enter a '

.

' character between digits.

·

CallSv =

This is the address of the H.323 gatekeeper. For IP Office systems this is the IP address of the IP Office LAN.

·

CallSvPort =

This is the Gatekeeper transport layer port number. For Avaya IP phones the value used should be

1719

. To

accept the current value, press # or enter a value and then press

#

.

·

Router =

This is the address of the phone's default IP gateway. For IP Office this is typically the IP address of the IP
Office LAN. To accept the current value, press

#

or enter a value and then press #.

·

Mask =

This is the phone's IP Mask (also called the subnet mask). The mask is used with the IP address to indicate the
phone's subnet. This should match the IP mask set for the IP Office Unit.

·

FileSv

=

This is the address of the file server from which the phone should request software and settings files. Enter the
address of the TFTP or HTTP configured with the Avaya IP phone software file set.

·

802.1Q =

To change the setting press

*

. Press

#

to accept the value.

·

VLAN ID =

For details of VLAN configuration see

VLAN and IP Phones

.

4. If you go through without changing anything, the phone displays

No new values

. Press

#

. If the phone displays

Enter command

, power off and on again.

5. Once all the values have been entered or the existing values accepted the phone will display

Save new values?

.

To save the values, press

#

. The phone will save the values and then restart using those values.

6. The

phone registration

menu is displayed.

47

60

50

«
...
46
47
48
49
50
...
»

Summary of Contents for one-X Deskphone SIP 9620C




































































































Reviews:

No comments