manualshive.com logo in svg

Avaya Media Gateway G350, Maintenance Manual

Share
Download
Avaya Media Gateway G350 Maintenance Manual Download Page 58

Avaya Communication Manager controlled maintenance
Dynamic Call Admission Control

58

Maintenance of the Avaya G350 Media Gateway

June 2004

NOTE:

In addition to the commands listed above, the 

save translations

 command is disabled in 

the case of an S8300 configured as an LSP. For an LSP, translations are received from the 
primary server, and there is no need to save them.

Dynamic Call Admission Control

In order to manage the flow of calls and voice data on the G350 most efficiently, the Media Gateway 
Controller must have real-time information about the network topology and currently available 
bandwidth. Without this, changes to the network structure, such as switching over to a backup line, can 
cause the network to become overloaded with voice data. The MGC, unaware of the switchover, 
continues to admit calls at the same volume, causing network congestion. Using the Dynamic CAC (Call 
Admission Control) feature, the G350 can provide the MGC with up-to-date information on the 
bandwidth available for voice data.

By default, G350 interfaces do not participate in Dynamic CAC. However, it is highly recommended to 
enable Dynamic CAC on the G350’s interfaces. If users report problems with long delays, jitter, and loss 
of calls, enable Dynamic CAC to provide greater link reliability and robustness. 

Enabling Dynamic CAC on the G350

Use the 

dynamic-cac

 command to enable Dynamic CAC on the G350. Dynamic CAC must be enabled 

on each interface responsible for providing call bandwidth. If Dynamic CAC is enabled on more than one 
interface, specify an activation priority for each interface. The BBL (Bearer Bandwidth Limit) is reported 
as the BBL of the interface with the highest activation priority. 

The dynamic-cac command has the following syntax:

dynamic-cac

 

bbl

 [

activation-priority

]

synchronization

tdm

tone-clock

Table 21: More Disabled SAT Commands   2 of 2

status

set

reset

busyout/release

test

  2 of 2

Table 22: Additional Disabled SAT Commands

backup

clear

duplicate

enable/disable

format

monitor

recycle

disk

interface

data-module

synchronization
-switch

card-mem

system 
(conn)

carrier

isdnpri-
testcall

disk

pgate-port

Summary of Contents for Media Gateway G350













































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands