Avaya J169 Installing And Administering Download

Page: 84 / 203

In addition, you can edit the settings file to customize phone parameters for your specific
environment.

Related links

Server Administration

on page 82

DHCP generic setup

This document describes the generic DCHPv4 and DHCPv6 administration that works with the IP
Deskphones.

Windows operating systems include several DHCP software alternatives such as:

• Windows 2008

DHCP Server

• Windows 2012

DHCP Server

Any DHCP application might work if the DHCP server is correctly configured.

Note:

Avaya does not assume responsibility for configuring your DHCP server. Contact your vendor
or supplier for configuring the DHCP server correctly.

Related links

Server Administration

on page 82

Setting up the DHCP server

About this task

DHCP server setup involves:

Procedure

1. Follow vendor instructions to install the DHCP server software.

2. Configure the DHCP server with:

• IP addresses available for the phone.

• The following DHCP options for using IPv4:

Option 1: Subnet mask

Option 3: Gateway (router) IP addresses

. If using more than one address, the total

list can contain up to 255 total ASCII characters. You must separate IP addresses
with commas with no intervening spaces.

Option 6: DNS servers address list

. If using more than one address, the total list

can contain up to 127 total ASCII characters. You must separate IP addresses with
commas with no intervening spaces. At least one address in Option 6 must be a valid,
dotted decimal address without a zero.

Administering your phone

May 2018

Installing and Administering Avaya J169/J179 IP Phone H.323

Comments on this document? [email protected]

Summary of Contents for J169












































































































































































































Search results

Summary of Contents for J169

Reviews:

Related manuals for J169

Brands by name

Popular brands

Avaya J169, Installing And Administering

Search results

Summary of Contents for J169

Reviews:

Related manuals for J169

Brands by name

Popular brands