Avaya J169 Installing And Administering Download

Page: 44 / 203

Restarting the phone

About this task

Use the following procedure to restart the phone.

Procedure

1. Select

RESTART PHONE

from the Craft Procedures screen. The phone displays the

following text:

Press Restart to confirm.

2. Press

Cancel

to return to the Craft Procedures screen without restarting the phone.

Press

Restart

to proceed with the registration steps.

A restart does not affect user-specified data and settings like Contacts data or the phone
login and password.

The completion of the restart procedure depends on the status of the boot and application
files.

Setting or changing the signaling protocol

About this task

Use the following procedure to set or change the Signaling Protocol Identifier. A valid SIG Protocol

Identifier is either 0 (default), 1 (H.323), or 2 (SIP).

Note:

Perform this procedure only if the LAN Administrator instructs you to do so.

Procedure

1. Select SIG from the Craft Local Procedures screen. The deskphone prompts you to use

the Right and Left navigation arrows to select a setting and displays the following text:

Sig: text string Choice Selector

where the

text string

is the wording associated with the current system value of SIG,

defined as:

•

Default

when SIG = 0

•

H.323

when SIG = 1

•

SIP

when SIG = 2

2. Press the Right or Left navigation arrow to navigate through the settings to change the

setting.

Initial setup and connectivity

May 2018

Installing and Administering Avaya J169/J179 IP Phone H.323

Comments on this document? [email protected]

Summary of Contents for J169












































































































































































































Search results

Summary of Contents for J169

Reviews:

Related manuals for J169

Brands by name

Popular brands

Avaya J169, Installing And Administering

Search results

Summary of Contents for J169

Reviews:

Related manuals for J169

Brands by name

Popular brands