Avaya J169 Installing And Administering Download

Page: 39 / 203

2. Press one of the following:

•

Clear

: To clear all values to use initial default values.

•

Cancel

: If you do not want to clear all values and to terminate the procedure and retain

the current values.

The phone displays the following text:

Clearing values...

The phone is reset to the default factory settings.

• All system values and system initialization values.

• 802.1X identity and password.

• User options, parameter settings, identifiers, and password.

• Any user data like Contact Lists or Call Logs are deleted.

After clearing the values, the phone resets.

Debug mode

About this task

You can use the debug mode to send all your debug data in a file, nnn_report.tar.gz where you

replace nnn by the deskphone extension as specified by the user during registration.

Note:

The DEBUG option is available for use only if you change the default password to the craft

menu through the PROCPSWD parameter. If you do not change the default password, the

option is available only in a read-only mode.

The new value of the PROCPSWD parameter must be 4 to 7 numeric digits, "0000" through

"9999999". However if value of PROCPSWD is less than 4 digits after you install Release

6.2.4 or later, the value will be changed back to the default value of 27238.

Procedure

1. Scroll and select DEBUG from the Craft Local Procedure Screen. Press

Start

. The

deskphone displays, the following text:

Setting

Options available

Serial Port

Adjunct/CLI/Disable

Log to file

On/Off

Phone Report

Navigate to

Phone Report

. Press

Create

to send the report to the backup

folder specified by BRURI.

Using local Administrative Menu procedures

May 2018

Installing and Administering Avaya J169/J179 IP Phone H.323

Comments on this document? [email protected]

Summary of Contents for J169












































































































































































































Search results

Summary of Contents for J169

Reviews:

Related manuals for J169

Brands by name

Popular brands

Avaya J169, Installing And Administering

Search results

Summary of Contents for J169

Reviews:

Related manuals for J169

Brands by name

Popular brands