Avaya J129 Installing And Administering Download

Page: 74 / 133

Avaya J129 IP Phone survivability in the Avaya Aura

environment

Primary Server

Session Manager

Third-party gateway

SIP Gateway

Branch Session

Manager

SURVIVABILITY SERVER

PRIMARY / SECONDARY
(FAILOVER) SERVER

PHONE

Session Manager

Secondary Server

Figure 5: Survivability in Avaya Aura

Note:

For more information on survivability about IP Office environment, see

Administering Avaya IP

Office Platform with Web Manager

Survivability controller determination

The order of precedence in determining the active controller is:

1. Phone user interface
2. PPM server

System failover

September 2017

Installing and Administering Avaya J129 IP Phone

Comments on this document? [email protected]

Summary of Contents for J129






































































































































Search results

Summary of Contents for J129

Reviews:

Related manuals for J129

Brands by name

Popular brands

Avaya J129, Installing And Administering

Search results

Summary of Contents for J129

Reviews:

Related manuals for J129

Brands by name

Popular brands