Avaya J129 Installing And Administering Download

Page: 64 / 133

Restarting the phone

Procedure

1. Press

Main Menu

Admin

2. In the

Access code

field, enter the admin menu password.

3. Press

Enter

4. Select

Restart phone

5. Press

Restart

when the phone prompts for confirmation.

A restart does not affect user-specified data and settings, such as contact data or the phone
login and password.

Configuring SIP settings

About this task

Use this procedure to set up SIP-related settings, such as identifying the SIP proxy server.

Note:

In IP Office the autogenerated

J100 settings.txt

includes the settings for the SIP servers

and protocols. The settings are based on the SIP values set in the IP Office system

configuration.

Procedure

1. Press

Main Menu

Admin

2. In the

Access code

field, enter the admin menu password.

3. Press

Enter

4. Select

SIP

5. Choose one of the following:

•

SIP global settings

•

SIP proxy server

6. Press

Select

to change any of the following SIP global settings:

•

Domain

: Changes the domain parameter of SIP.

•

Avaya Environment

: Specifies whether the available SIP Avaya environment is in effect.

The two modes to detect the available environment are as follows:

Auto

: Detects the Avaya environment automatically.

: Does not detect the Avaya environment and switches to a non-AST mode.

Phone administration and configuration

September 2017

Installing and Administering Avaya J129 IP Phone

Comments on this document? [email protected]

Summary of Contents for J129






































































































































Search results

Summary of Contents for J129

Reviews:

Related manuals for J129

Brands by name

Popular brands

Avaya J129, Installing And Administering

Search results

Summary of Contents for J129

Reviews:

Related manuals for J129

Brands by name

Popular brands