Avaya J129 Installing And Administering Download Page 45

Page: 45 / 133

Destination port

Source port

Use

Protocol

UDP or TCP

(TLS over TCP).
Responses to SIP
messages initiated by the
phone should be sent to
the number used in the
Source Port field of the
message from the phone.
The number used in the
Source Port field of the
DNS query that the
phone sends

Any

Received DNS
messages

UDP

The number used in the
Source Port field of the
SNTP query that the
phone sends

Any

Received SNTP
messages

UDP

161

Any

Received SNMP
messages

UDP

Transmitted packets (source = SIP phone)

Destination port

Source port

Use

Protocol

UDP or TCP

Any unused port number

Transmitted DNS
messages

UDP

Transmitted DHCP
messages

UDP

80, unless explicitly
specified otherwise

Any unused port number

Packets transmitted by
the HTTP client of the
phone

TCP

123

Any unused port number

Transmitted SNTP
messages

UDP

The number used in the
Source Port field of the
SNMP query packet
received by the phone

161

Transmitted SNMP
messages

UDP

443, unless explicitly
specified otherwise

Any unused port number

TLS/SSL packets
transmitted by the HTTP
client of the phone.

TCP

514

Any unused port number

Transmitted Syslog
messages

UDP

Table continues…

TCP and UDP ports

September 2017

Installing and Administering Avaya J129 IP Phone

Comments on this document? [email protected]

Summary of Contents for J129






































































































































Search results

Summary of Contents for J129

Reviews:

Related manuals for J129

Brands by name

Popular brands

Avaya J129, Installing And Administering

Search results

Summary of Contents for J129

Reviews:

Related manuals for J129

Brands by name

Popular brands