Avaya J100 Series Installing And Administering Download Page 87

Page: 87 / 528

•

SSID

: Specifies the network name for the WLAN you are using. Use the navigation key

to select another SSID.

•

Wi-Fi networks

: Displays available WLAN.

7. Use the navigation key to select a WLAN, and press

Connect

8. Press one of the following:

•

Save

•

Cancel

•

Change

Configuring SIP settings

About this task

Use this procedure to set up SIP-related settings, such as identifying the SIP proxy server.

Before you begin

To use TLS signaling, ensure ENFORCE_SIPS_URI is set to 0.

Procedure

1. Press

Main Menu

Admin

2. In the

Access code

field, enter the admin menu password.

3. Press

Enter

4. Select

SIP

5. Choose one of the following:

•

SIP global settings

•

SIP proxy server

6. Press

Select

to change any of the following SIP global settings:

•

SIP Domain

: Changes the domain parameter of SIP.

•

Avaya Environment

: Specifies whether the available SIP Avaya environment is in

effect.

The two modes to detect the available environment are as follows:

Auto

: Detects the Avaya environment automatically.

: Does not detect the Avaya environment and switches to a non-Aura mode.

Note:

Disable the Avaya Environment configuration from the

46xxsettings.txt

file.

•

Registration policy

: Specifies the registration policy for SIP.

Configuring the phone using Administration menu

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Search results

Summary of Contents for J100 Series

Reviews:

Avaya J100 Series, Installing And Administering, Page: 87 / 528

Search results

Summary of Contents for J100 Series

Reviews: